Happy Thanksgiving from Bailiff Enterprises! Our office and plant will be closed Thursday, November 26 and Friday, November 27, 2026. We reopen Monday, November 30.

Fittings & Options · Welded fittings

Welded Flanges & Couplings for Plastic Tanks

A welded fitting is fused into the tank wall, so there is no gasket between the fitting and the tank. We weld ANSI 150 flanges, threaded couplings and spin weld fittings into polyethylene, polypropylene and PVDF tanks at our plant in Willis, Texas.

FittingConnectionSizesBest for
Welded flangeANSI 150 bolted flangePolyethylene ¾″–30″; polypropylene 1″–10″; PVDF ½″–11″Large outlets, pump suction lines and connections to flanged valves and piping.
Welded couplingFemale pipe thread (FNPT)Polyethylene and polypropylene 1″–4″; PVDF ½″–6″Threaded connections with no gasket at the tank wall.
Spin weld fittingFemale pipe thread (FIPT)Small sizes, ¼″ to 3″Small polyethylene connections such as drains, gauges and sample ports.
Oxidizing chemicals: we do not install welded flanges in the sidewall of tanks that will hold nitric acid, sodium hypochlorite, sulfuric acid or other oxidizing chemicals. Ask us about the best fitting for these tanks.

Welded flanges (ANSI 150)

Our welded flanges are raised-face ANSI 150 flanges. Each one has two parts:

  • a stub end (flange adapter) made from the same material as the tank (HDPE, polypropylene or PVDF) and welded to the tank wall; and
  • a Vanstone-style loose backing ring that slides over the stub end and takes the bolts. Because the ring turns freely, it lines up easily with the bolt holes on your valve or pipe flange.

By default the back of the flange ring sits 4″ out from the tank wall; you can specify up to 6″. Flanges are raised face unless a flat face is quoted.

Large welded flange with bolted blind flange on a plastic tank
Large welded flange with a blind flange bolted on.
HDPE stub end flange adapter
Stub end (flange adapter).
Vanstone style loose backing ring for an ANSI 150 welded flange
Vanstone loose backing ring.
Welded flange stub end with support gussets ready to weld to a tank
Stub end with support gussets.
Black HDPE tank with welded flanged outlets on the sidewall
Welded flanges on a black HDPE tank.

Flange (loose ring) dimensions, inches

SizePart no.D (OD)LNRBolt circle
½854-0053 1/211/819/322 3/8
¾854-0073 7/81 5/321/819/322 3/4
1854-0104 1/41 3/81/821/323 1/8
1¼854-0124 5/81 1/21/811/163 1/2
1½854-01551 11/161/43/43 7/8
2854-02061 3/43/1613/164 3/4
3854-030FT7 19/322 1/83/1616
4854-040FT9 1/162 1/21/41 7/327 7/16
5854-050FT102 7/81/41 1/48 1/2
6854-060FT10 15/163 9/321/41 5/169 1/2
8854-080FT13 9/164 1/21/41 1/211 3/4
10854-100FT1667/161 9/1614 3/8
12854-120FT19 1/327 17/329/161 11/1617

FT = FiberTuff ring. Stub ends come in IPS sizes 2″ to 20″.

Bolting a welded flange

The loose rings are fiberglass-filled PVC, and they can be damaged if the bolts are over-tightened. When you connect to a welded flange:

  • Use two wide flat washers per bolt, one under the head and one under the nut.
  • Keep threads clean and well lubricated.
  • Tighten in the star pattern shown, in stages, to the torque in the table.
Star tightening pattern for 4, 8 and 12 bolt flanges
Tightening order for 4, 8 and 12 bolt flanges.
Flange sizeBolt holesBolt dia.Min. bolt lengthTorque (ft-lb)
½″ – 1½″4½″2″ – 2½″15–20
2″ – 3″4⅝″3″ – 3½″20–30
4″8⅝″3½″20–30
6″ – 8″8¾″4″ – 4½″33–50
10″ – 12″12⅞″5″53–75

Spec sheets: Welded flanges (PDF) Flange dimensions (PDF) Stub end dimensions (PDF) Bolt torque settings (PDF)

Welded couplings

A welded coupling is a threaded socket (female pipe thread) welded into the tank wall. It gives you a threaded connection with no gasket at the tank, which suits chemicals that are hard on gaskets. We weld couplings into polyethylene and polypropylene tanks in 1″ to 4″ and into PVDF tanks in ½″ to 6″. On double wall tanks, couplings can pass through both walls.

Welded couplings spec sheet (PDF) · Welded fittings overview (PDF)

Black polyethylene welded couplings with female pipe threads for plastic tanks
Welded FNPT couplings.

Spin weld fittings

Spin weld fittings are polyethylene fittings that are spun against the tank wall at high speed until the friction melts and fuses them in place. They make small threaded connections, from ¼″ to 3″ female pipe thread, for drains, gauges, sample ports and similar uses on polyethylene tanks. Matching caps close off unused openings.

Polyethylene spin weld tank fittings
Spin weld fittings.
Polyethylene spin weld caps for plastic tanks
Spin weld caps.

Spin weld fittings spec sheet (PDF)

Need a gasketed, removable fitting instead? See bulkhead fittings and bolted flanges.

Need a welded outlet on your tank?

Tell us the size, location and chemical, and we will quote the tank with the fittings welded in. Request a quote · dmiller@plasticstoragetanks.com

★ Tank Wizard