Fittings & Options · Welded fittings
A welded fitting is fused into the tank wall, so there is no gasket between the fitting and the tank. We weld ANSI 150 flanges, threaded couplings and spin weld fittings into polyethylene, polypropylene and PVDF tanks at our plant in Willis, Texas.
| Fitting | Connection | Sizes | Best for |
|---|---|---|---|
| Welded flange | ANSI 150 bolted flange | Polyethylene ¾″–30″; polypropylene 1″–10″; PVDF ½″–11″ | Large outlets, pump suction lines and connections to flanged valves and piping. |
| Welded coupling | Female pipe thread (FNPT) | Polyethylene and polypropylene 1″–4″; PVDF ½″–6″ | Threaded connections with no gasket at the tank wall. |
| Spin weld fitting | Female pipe thread (FIPT) | Small sizes, ¼″ to 3″ | Small polyethylene connections such as drains, gauges and sample ports. |
Our welded flanges are raised-face ANSI 150 flanges. Each one has two parts:
By default the back of the flange ring sits 4″ out from the tank wall; you can specify up to 6″. Flanges are raised face unless a flat face is quoted.





| Size | Part no. | D (OD) | L | N | R | Bolt circle |
|---|---|---|---|---|---|---|
| ½ | 854-005 | 3 1/2 | 1 | 1/8 | 19/32 | 2 3/8 |
| ¾ | 854-007 | 3 7/8 | 1 5/32 | 1/8 | 19/32 | 2 3/4 |
| 1 | 854-010 | 4 1/4 | 1 3/8 | 1/8 | 21/32 | 3 1/8 |
| 1¼ | 854-012 | 4 5/8 | 1 1/2 | 1/8 | 11/16 | 3 1/2 |
| 1½ | 854-015 | 5 | 1 11/16 | 1/4 | 3/4 | 3 7/8 |
| 2 | 854-020 | 6 | 1 3/4 | 3/16 | 13/16 | 4 3/4 |
| 3 | 854-030FT | 7 19/32 | 2 1/8 | 3/16 | 1 | 6 |
| 4 | 854-040FT | 9 1/16 | 2 1/2 | 1/4 | 1 7/32 | 7 7/16 |
| 5 | 854-050FT | 10 | 2 7/8 | 1/4 | 1 1/4 | 8 1/2 |
| 6 | 854-060FT | 10 15/16 | 3 9/32 | 1/4 | 1 5/16 | 9 1/2 |
| 8 | 854-080FT | 13 9/16 | 4 1/2 | 1/4 | 1 1/2 | 11 3/4 |
| 10 | 854-100FT | 16 | 6 | 7/16 | 1 9/16 | 14 3/8 |
| 12 | 854-120FT | 19 1/32 | 7 17/32 | 9/16 | 1 11/16 | 17 |
FT = FiberTuff ring. Stub ends come in IPS sizes 2″ to 20″.
The loose rings are fiberglass-filled PVC, and they can be damaged if the bolts are over-tightened. When you connect to a welded flange:

| Flange size | Bolt holes | Bolt dia. | Min. bolt length | Torque (ft-lb) |
|---|---|---|---|---|
| ½″ – 1½″ | 4 | ½″ | 2″ – 2½″ | 15–20 |
| 2″ – 3″ | 4 | ⅝″ | 3″ – 3½″ | 20–30 |
| 4″ | 8 | ⅝″ | 3½″ | 20–30 |
| 6″ – 8″ | 8 | ¾″ | 4″ – 4½″ | 33–50 |
| 10″ – 12″ | 12 | ⅞″ | 5″ | 53–75 |
Spec sheets: Welded flanges (PDF) Flange dimensions (PDF) Stub end dimensions (PDF) Bolt torque settings (PDF)
A welded coupling is a threaded socket (female pipe thread) welded into the tank wall. It gives you a threaded connection with no gasket at the tank, which suits chemicals that are hard on gaskets. We weld couplings into polyethylene and polypropylene tanks in 1″ to 4″ and into PVDF tanks in ½″ to 6″. On double wall tanks, couplings can pass through both walls.
Welded couplings spec sheet (PDF) · Welded fittings overview (PDF)

Spin weld fittings are polyethylene fittings that are spun against the tank wall at high speed until the friction melts and fuses them in place. They make small threaded connections, from ¼″ to 3″ female pipe thread, for drains, gauges, sample ports and similar uses on polyethylene tanks. Matching caps close off unused openings.


Spin weld fittings spec sheet (PDF)
Need a gasketed, removable fitting instead? See bulkhead fittings and bolted flanges.
Need a welded outlet on your tank?
Tell us the size, location and chemical, and we will quote the tank with the fittings welded in. Request a quote · dmiller@plasticstoragetanks.com