Happy Thanksgiving from Bailiff Enterprises! Our office and plant will be closed Thursday, November 26 and Friday, November 27, 2026. We reopen Monday, November 30.

Home › Fittings & Options › Heat Tracing

Heat Tracing

Heat trace pads on the tank wall, under the insulation, keep the liquid from freezing and hold it at the temperature your process needs.

Freeze protection

The main job of heat trace on a plastic tank is freeze protection. Water-based chemicals, fertilizers and process fluids can freeze at or near 32°F (0°C), which can damage the tank, crack fittings or block outlets. Heat trace keeps the contents above the freezing point.

Viscosity control

Some liquids, such as adhesives, surfactants and certain agricultural chemicals, thicken or solidify in cold weather and become hard to pump. Heat trace holds them at a temperature where they pump and meter consistently.

Insulation is required

Heat trace is always installed with spray foam insulation. The pads are attached to the tank, then the foam is sprayed over them and sealed with a white mastic coating. See tank insulation.

Pads and controller

  • Ultra-low watt density, flexible, waterproof heating pads with adhesive backing, made for heat-sensitive plastic tanks
  • Two pad sizes and power outputs, sized to the tank, its location, the chemical and the temperature you need to hold
  • Microprocessor controller with process temperature control and high-limit protection, for up to 6 heaters
  • High-temperature, low-temperature and low-current alarms, with an alarm contact for your control system
  • NEMA 4X, IP66 enclosure; 100–277 VAC power
Heat tracing and other optional equipment carry the manufacturer’s warranty. See our warranty.

The heat trace package

We bond HTD Heat Trace SPX heating pads to the sidewall of the tank and wire them to a 2XTC controller. The controller holds your setpoint, and a separate high-limit sensor keeps the pads from ever overheating the plastic. Pads run at 0.39 watts per square inch and can hold liquid up to 150°F; complete systems run from 210 W to 4,200 W.

SPX heat trace pad with cold lead for a plastic tank
SPX pad with cold lead.
2XTC heat trace controller for a plastic tank
2XTC controller.

Pads: SPX 210 / 420

PowerSPX 210: 210 W · SPX 420: 420 W
Size30″ × 18″ (210) · 60″ × 18″ (420)
Watt density0.39 W/sq. in.
Voltage120 VAC (240 VAC on request)
Max. maintain temp.150°F (66°C)
Max. exposure temp.220°F (104°C)
Min. install temp.50°F (10°C)
Min. tank diameter36″ (18″ bend radius)
ConstructionMulti-path parallel circuit in waterproof epoxy-glass laminate, aluminum ground shield
ProtectionInternal over-temperature thermostat
Cold lead3-conductor 16 AWG, TPE jacket, tinned copper braid; available in 10, 16, 20 or 24 ft (SPX 420)
MountingAdhesive back; edges sealed with aluminum tape

Controller: 2XTC

Power input100–277 VAC, 50/60 Hz
Heater output30 A SPST relay, active arc suppression
Process setpoint0–200°F, on/off with adjustable band
High limit0–250°F, separate sensor
AlarmsLow temp., high temp., low current (current test every 24, 168 or 720 hrs)
Alarm outputsRelays, 5 A at 277 VAC, open or close on alarm
Remote output4–20 mA process temperature
Sensors1,000 Ω platinum RTD, 2-wire
Ambient−40° to 113°F
EnclosureNEMA 4X / IP66 polycarbonate
ApprovalsUL 508, CSA 22.2 #14

Standard systems

PadsWattsAmps at 120 VControllers
1 × SPX 2102101.751
2 × SPX 2104203.51
1 × SPX 210 + 1 × SPX 4206305.251
2 × SPX 42084071
3 × SPX 4201,26010.51
4 × SPX 4201,680141
5 × SPX 4202,10017.51
6 × SPX 4202,520211
7 × SPX 4202,94024.52
8 × SPX 4203,360282
10 × SPX 4204,200352

How we size a heat trace system

We look at two things:

  • The size of your tank.
  • How much warmer the liquid has to stay than the coldest outside air. For example, if it can drop to 10°F outside and the liquid must stay at 50°F, the difference is 40°F.

We have sizing charts for every vertical and double wall tank we sell, for differences from 30°F up to 100°F.

Bigger systems use two controllers, each running half of the pads.

The heat pads go on the tank under the insulation. The tank is hydro-tested before it ships.

Specifications from HTD Heat Trace SPX and 2XTC data sheets. SPX and 2XTC are products of HTD Heat Trace. Specifications subject to change.

Downloads

Heat Tracing Spec Sheets

Heat tracing and insulated, heat-traced tank packages for plastic storage tanks.

Insulation, heat tracing & tie-downs

Talk to a tank specialist

Ready to Price a Double Wall Tank?

★ Tank Wizard